The purpose of this document is to detail the installation and configuration of iDirect satellite modems for use with Lantronix appliances.
LMS 6.0 includes support for iDirect satellite modems including 8000, 7000, 5000, 3000, X3, X5 series standalone, and iConnex models.
In a terrestrial or fixed installation, connect a standard Cat5/patch cable between an available Lantronix port and the console port of the iDirect modem.
In the maritime or mobile environments, key information is passed between the antenna and the modem. With the Lantronix appliance managing the modem via a console connection, it is necessary to create a split cable for this information to pass directly between the antenna and modem uninterrupted. There are two pins carrying key information between the antenna and the modem: RJ-45 pin 2 which carries the AGC threshold information and RJ-45 pin 7 which carries TX Mute. Below is an example wiring diagram describing the split cable configuration. This cable is available as Lantronix part number UP610031 CABLE,UPLOGIX-iDIRECT-SEATEL NO CONNECTOR, or UP610033 CABLE,UPLOGIX-iDIRECT-SEATEL DB25.
For example, the Sea Tel terminal mounting strip wiring diagram is displayed below.
Use a workstation to open a command line session with the Lantronix appliance.
Issue the port command to switch to navigate to the port your iDirect modem is connected to. In the example below the iDirect modem is attached to port 2.
[admin@LantronixLM]# port 1/2 native [admin@LantronixLM (port 1/2)]#
Use the config init command to configure the port for iDirect.
[admin@LantronixLM (port1/2)]# config init --- Enter New Values --- description: : iDirect make: [embedded]: iDirect model: os: :infiniti os version: : management IP: : configure dedicated ethernet port? (y/n) [n]: console username: : root console password : ******** confirm console password : ******** enable username: : admin enable password :******** confirm enable password :******** serial bit rate : 9600 serial data bit : serial parity [none]: serial stop bit : serial flow control [none]: use null modem (rolled cable to device)? (y/n): n Do you want to commit these changes? (y/n): y
Issue the terminal command to start a terminal session with the modem. This session takes place within your Lantronix appliance session.
[admin@LantronixLM (port1/2)]# terminal Press ~[ENTER] to exit Connecting ... Retrieving running-config from device ... Complete. config pulled. running-config saved to archive as current. Console session started.
Upon login you should see the iDirect prompt.
[RMT:361] admin@telnet:127.0.0.1 >
Monitors collect chassis and interface data from supported devices. The results can be used to trigger an alarm, event or to take other automated actions. There are six monitors for the iDirect modem: chassis, interface, remotestate, ping, consoleLog and terminal.
When the modem is initialized using the config init command, the chassis and console log monitor will automatically be scheduled.
Additional monitors to capture information on RF statistics from the modem can be scheduled using the config monitor
[admin@LantronixLM (port1/2)]# config monitor remotestate
The results of monitors can be viewed with the show
In maritime/mobile configurations, the Lantronix may be required to regularly supply GPS coordinates to the iDirect over the console port. In order to provide this information accurately, the Lantronix must have a source for GPS coordinates with data no more than two hours old. The Lantronix can monitor an external GPS source such as a ship's compass or dedicated GPS antenna to capture this information.
Additionally, the coordinates may be monitored from a supported antenna controller. Once the coordinates are collected by the Lantronix appliance, they can then be sent to the iDirect on a configurable basis using the config schedule command at the port level. In the example below, the scheduled task sends the coordinates to the iDirect every 60 seconds by issuing the iDirect latlong command on the console.
config schedule setPosition -d 60
GPS coordinates may also be issued as a response to the Consolelog monitor.
Collecting and monitoring syslog messages from the iDirect modem is configured with the config init command and can be viewed by issuing the following command:
show device syslog
A rule can then optionally be applied to check for string matches allowing for log analysis and action-based responses. In the example below, the appliance is configured to search for a message indicating the GPS coordinates are not available and send the coordinates when that event occurs.
config monitor consoleLog Send_Lat_Lon_On_Unavailable_Message
The Lantronix file system is a repository for configuration, OS and post files for the managed iDirect.
To view the files in the Lantronix file system for your device, use the show directory command:
[admin@LantronixLM (port1/1)]# show directory Type Version Name ------- --------- ------------ Config Running Current running-config Previous running-config Startup Current startup-config Previous startup-config OS 711 remote-7_1_1.pkg Post Current readPost
Users can name specific versions of configurations and operating system files. These named versions can be referenced in rules. For more information about our user named versions please see the User-Defined Versions Feature Guide.
Lantronix RMOS supports management of option files. The startup configuration and running configuration can be pulled from the iDirect and saved on the Lantronix using the pull command. In addition, the running configuration, startup configuration, and operating system images saved on the Lantronix can be pushed to the iDirect using the push command. Finally, all of the files stored on the Lantronix can be copied to or from the port using the copy command.
The Local Manager can be used to manage the running configuration which contains the startup configuration (falcon.opt or show Option file) and also various runtime parameters. Managing a running configuration through Lantronix will use options set commands for each parameter and can rollback changes accordingly if required.
When pushing a new running configuration, reboot is available with the -reboot switch. The command for pushing the running configuration is push running-config <previous|candidate|current|
The Local Manager can also be used to manage the startup configuration which contains the option file (falcon.opt). When managing startup configurations through Lantronix, the appliance will utilize the Linux interface and push over the falcon.opt file rather than set the individual parameters in the Falcon interface. Pushing the startup configuration also allows an optional service level or system level reboot upon confirmation.
Lantronix supports management of operating system files. Both Base Software Packages (BSPs) and Remote Application files can be copied from and pushed to the iDirect via the Lantronix.
To copy operating system candidates to the iDirect port, use the copy command.
The Lantronix iDirect driver has the ability to push operating system images to the iDirect with the push os command. Pushing an operating system requires IP connectivity from the Lantronix to the iDirect. In the example below, the operating system file, 1003 is pushed to the iDirect.
[admin@LantronixLM (port1/2)]# push OS 1003 Transfering 3893765 bytes Verifying checksum: 8b8897b7ac1fd854e46f29cf146ff416 Wating for package install (up to 300 seconds) Issuing 'request system reboot' Reading post Device loaded Post complete. Hostname : Serial Number: 288 Make : iDirect Model : X5 OS Type : iNFINITI OS Version : app:10.0.0.3, bsp:10.0.0.3 Uptime : 0 mins 8.32 secs Push OS succeeded.
When pushing BSPs and Remote Application (the Falcon Service) files, it is required to push the BSP first, as it should be kept at a higher version # than the Remote Application.
The Lantronix iDirect driver does not have the ability to retrieve the Package Files from a managed iDirect device, but they remain in the Lantronix file system as an operating system candidate when the Lantronix performs the upgrade process.